ESCO Brazing and Soldering Practice Test

These questions are part of the practice quiz. Start practicing

• Which set of components is required for both brazing setups?
• Which torch kit pair is primarily used for brazing?
• To break the oxide layer on aluminum and achieve wetting, which approach is commonly used?
• What indicates the temperature target has been reached in a brazing cycle?
• What is the typical purpose of a brazing furnace in industry?
• Displays tank pressure:
• What is the effect of poor fit-up on filler metal consumption?
• Describe a typical fillet brazed joint geometry.
• What challenge do dissimilar metals pose in brazing, and how is it mitigated?
• What is used during the soldering process to prevent oxides from forming and to help molten solder flow into the joint?
• One of the most critical tasks performed when brazing is to adjust what?
• Define dwell time in a brazing cycle.
• Name two primary families of solders used in electronics and describe their melting characteristics.
• Which component changes flame size?
• What should be done to the tubing around the copper prior to assembly?
• Brazing is typically performed in which temperature range?
• Which of the following is NOT a gauge or control on a standard regulator described?
• After any method used to join the copper tubing, what is the first task to perform?
• What device controls the pressure of gas from the cylinder to the torch?
• Which copper tubing types are available in both rigid sections and rolls of soft (annealed) tubing?
• Which tool is used to cut copper tubing?
• Two common types of copper tubing?
• Which copper tubing type is thinner than Type K and is blue?
• During brazing, which step comes first in the general brazing procedure?
• Which action is not part of the CCAACI general solder procedure?
• When brazing stainless steel, which flux characteristics are important?
• Which color identifies Type L copper tubing?
• Which statement is true about leak testing?
• Which option is NOT a function of flux in brazing?
• Cutting copper tubing will be a _______ process because tubing can be bent or crushed if rushed.
• Which tubing cutters are used to cut copper in close quarters?
• What should be considered when disposing of flux from brazing operations?
• What is a typical role of flux in brazing?
• After soldering or brazing, what should you do before handling to avoid burns?
• Which two torch kits are primarily used for brazing?
• What is the process called when the end of a copper tube is expanded for brazed or soldered joint?
• Which flame has slightly more acetylene than the 1:1 ratio and features inner cone, acetylene feather, and outer cone?
• What is the term for joining tubing without flame using a powered crimping tool?
• Which gas should be used to purge copper tubing during brazing?
• What flux types are commonly used for electronics soldering?
• Which flame type has a 1:1 oxygen to acetylene ratio and has no chemical effect on the metals being brazed?
• The filler metals used for the brazing process are called what?
• To change flame size on a torch, what should you do?
• Once a leak is discovered, the leak site should be ______ and prepared for brazing or soldering.
• Soldering is performed at temperatures below 840 degrees Fahrenheit. Which process is described?
• Which non-torch heating method can be used in brazing?
• Which process joins tubing by melting a filler metal into the joint at temperatures above 840 degrees Fahrenheit?
• During the brazing process, which gas should be purged through the copper tubing to prevent oxidation or scale formation?
• Before brazing, which step involves cleaning the pieces to be brazed?
• Besides joint fit-up and wettability, what other factor strongly influences capillary flow in brazing?
• Which practice is characteristic of brazing in a controlled atmosphere?
• What happens when the joint clearance is too little in brazing?
• Which of the following is a direct consequence of preheating a brazing joint?
• Which are the most common types of torch flames?
• What is a common degreasing step in brazing preparation?
• Which inspection method would best detect a lack of filler metal at a joint interior?
• Which of the following is NOT a primary visual criterion for a sound brazed joint?
• Soft copper ___ be bent; rigid copper ______ be bent.
• What are the three primary visual criteria for a sound brazed joint?
• How does coefficient of thermal expansion mismatch affect solder joints during thermal cycles?
• Before soldering, how should the workpieces be prepared?
• Under what circumstance should flux residues be removed after brazing?
• How many leak detection methods are used for locating small leaks?
• Which inspection method detects surface-only imperfections in brazed joints?
• The measurement used for ACR copper tubing?
• Why is a flux residue often tested for corrosivity?
• Name three common brazed joint configurations.
• In brazing, what is the effect of excessive joint clearance on heat input and filler metal requirements?
• If the flare is done incorrectly, what is the primary risk?
• Maximum regulator pressure on an air acetylene tank should not exceed which PSIG?
• What is a standard method to verify brazed joint integrity for fluid systems?
• To help prevent leaks, the tubing should be cut with a ______ _____ for a clean, right-angle cut.
• Which joint geometry helps reduce thermal stress in soldering?
• What is the process called when expanding the end of copper tube into a funnel shape to fit onto threaded male fittings?
• Should always be used when working with nitrogen?
• Used to adjust the outlet pressure:
• Which method shows bubbles or foams at a leak?
• Which step should follow the initial leak test and precede charging?
• What is the final action in the brazing procedure CCASACI?
• Pressurize the system with dry nitrogen to inspect for _____.
• Which statement about brazing is true?
• What does wetting mean in soldering, and how can it be promoted?
• Which heat sources can be used to heat tubing during the soldering process?
• Which statement about Types K and L is true?
• In brazing, what indicates that the temperature target has been reached during the cycle?
• What is the primary objective of the ESCO Brazing and Soldering Practice Test?
• Which copper tubing type has the thinnest wall and is used for low-pressure applications?
• What environmental condition is typical for brazing operations to achieve high-quality joints?
• On oxyacetylene brazing kits, what ratio and pressures are typical?
• Which method is preferred for mini-split systems and avoids flaming action?
• What is an advantage of induction heating in brazing?
• Which condition most likely disrupts capillary flow in a brazed joint?
• Which non-torch heating method is used for brazing in a controlled atmosphere?
• In the leak response sequence, which action is taken on the leak site after discovery before repair?
• After passing the leak test, the system should be ______ prior to being charged.
• What is the main function of flux in brazing?
• After starting the nitrogen purge, what is the next action in brazing?
• Which tank size is commonly labeled as 'B' in oxy-fuel systems?
• Which device detects the trace gas at the leak?
• The HVACR industry typically uses what flare angle for copper tubing?
• Which color identifies Type K copper tubing?
• Why is surface cleanliness critical before brazing or soldering?
• Which tool and features will make a perfect flare for a good seal?
• How does brazing differ from welding in terms of metallurgical bonds?
• Which statement about flux residues is true?
• Brazing filler metals typically contain what percentage of silver?
• Why choose a no-clean flux in brazing or soldering?
• Which safety practice is essential when brazing to prevent inhaling fumes?
• On the regulator, displays outlet pressure:
• Which sequence correctly represents the general solder procedure abbreviated by CCAACI?
• Which nondestructive test methods are commonly used to evaluate brazed joints?
• Brazing temperatures range from which values?
• Why would vacuum or controlled-atmosphere brazing be preferred when brazing dissimilar metals?
• Which method is used to join copper tubing by creating a flare at the end of the tube?
• Why is flux important in preventing oxidation during brazing?
• Which copper tubing type has the thickest wall and is rated for the highest pressures and underground applications, and is green?
• In brazing, the bond is created by which mechanism?
• What design feature supports capillary flow in larger-diameter brazed joints?
• Which item is explicitly recommended to protect the surroundings during brazing or soldering?
• During pressure testing, which pressure value should be used from the listed options?
• This topic covers PPE, ventilation, fire prevention, and related safety measures during brazing or soldering.
• Which statement defines silver brazing and explains its use?
• Which test is used for high-sensitivity leak detection in brazed joints?
• Which components comprise the torch assembly?
• Air acetylene torches typically use which tanks?
• What is the purpose of post-braze annealing for certain joints?
• Which temperature is associated with a brazing flame described as producing a sharp flame?
• Which instrument detects the trace gas used in leak detection?
• Why is controlled heating important when brazing dissimilar metals?
• Which flame source produces a sharp flame at about 5400 degrees Fahrenheit?
• In what scenario would vacuum or controlled-atmosphere brazing be preferred?
• What is the purpose of preheating a joint before brazing?
• Once the tube has been cut, the end should be ________ or ______ to clear away burrs.
• What is the recommended surface preparation sequence for aluminum prior to brazing to promote wetting?
• What three properties of a brazing filler metal influence joint performance?
• Which copper tubing type is commonly used for residential water piping and ACR applications and is thinner than Type K?
• In brazing, which mechanism is primarily responsible for forming the joint?
• What is the difference between a brazed joint and a soldered joint when it comes to temperature range?
• Which factor matters most when selecting a brazing filler metal for a copper-to-brass joint?
• What practice reduces lead exposure risk when soldering?
• After repair is completed, the system should be ________ tested again for leaks.
• Which color identifies Type M copper tubing?
• In brazing, which material must have a melting point lower than that of the tubing being brazed?
• What are two common post-braze cleaning methods?
• In oxyacetylene kits, which tank is used for acetylene and what is its typical volume?
• What effect does overheating have on a brazed joint?
• Which flame produces a cooler flame at 3000 degrees Fahrenheit?
• What shape does the tube end take after proper flaring and is essential for sealing?
• Which accessory is used to ignite the gas mixture?
• Copper has a melting point of approximately which temperature?
• After assembling the pieces, what is the next step in the brazing procedure mnemonic CCASACI?
• Which of the following are examples of solder?
• Dye penetrant testing is primarily used to detect which type of defect?
• Which device detects the sound of a leak?
• Which term refers to the oxyacetylene flame?
• A roll of softer filler metal used in brazing or soldering is called what?
• In leak testing, a drop in temperature indicates which condition?
• What is the general brazing procedure called?
• Which option is NOT a leak detection method used for locating small leaks?
• What is a major health and safety concern when using lead-containing solders?
• Which description best matches a typical fillet brazed joint geometry?
• Which flame has slightly more oxygen than the 1:1 ratio and promotes the oxidation of copper and should not be used for copper brazing?
• Which flux type is particularly effective for stainless steel due to active wetting?
• What is a common defect associated with poor fit-up in brazing?
• Which tool combination will make a perfect flare end for a good seal?
• In design for capillary flow, which features create consistent capillary paths?
• What is the main purpose of using a 45-degree flare angle in copper tube connections?
• What is the fundamental metallurgical difference between brazing and soldering?
• What property of a joint primarily governs the success of capillary flow in brazing?
• What is the role of a heat sink in brazing?
• What is the melting point of copper?
• In the trace gas method, a trace amount of refrigerant is added to which gas?
• Which practice helps maintain joint clearance during brazing?
• What is a typical cause of lack of wetting in brazing?
• Why is proper fixturing important in brazing?
• One of the most common sources of system leaks is which issue?
• What is the process by which copper (when heated and cooled) becomes soft and is able to be bent/formed without cracking?